| 2024 Peterbilt 548 | STANDARD |
| Chassis load rating shall be 37,000 lbs. (GVWR) | STANDARD |
| wheelbase 166 @ 96.5 CA | STANDARD |
| CA 96.5 @ 166 wheelbase | STANDARD |
| BBC 109 | STANDARD |
| The entire length of the frame rails shall be full depth including the manufacturers integral frame extension. | STANDARD |
| RBM 3,468,000 with Section Modulus 28.9? | STANDARD |
| The section modulus at the Motor cut outs shall be at least 18.00, with an RBM of 2,000,000. | STANDARD |
| There shall be no holes or bolts in the top flange of the frame rails. There should be no holes full length on top flange. | STANDARD |
| The left frame rail shall be clear, between the fuel tank and the front hanger of the rear spring assembly | STANDARD |
| Cross-members shall not be riveted to the frame rails, however cross-member components may be riveted to form a cross-member assembly | STANDARD |
| Shall have a formed steel front bumper, with two front tow loops or hooks accessible through the bumper | STANDARD |
| Shall be a manufacturer?s premium cab with at least 21 inches of clear space between the driver and passenger seat. | STANDARD |
| Exterior of the Cab shall be painted with Sikkens basecoat /clear coat Omaha Orange 0311 or equal. | STANDARD |
| When the hood and fenders are tilted forward, the grill shall not come in contact with the front frame extension. | STANDARD |
| Three-piece bonded hood and fenders shall tilt forward to a stable position and allow full and unrestricted access to the Motor compartment | STANDARD |
| Voltmeter gauge | STANDARD |
| Motor oil pressure gauge. | STANDARD |
| Tachometer and Hour meter | STANDARD |
| Visual and audible low oil pressure / high coolant temperature warning system | STANDARD |
| Motor coolant temperature gauge | STANDARD |
| High output heater w/fresh air selection. The heater shall have a 30,000 BTU rating | STANDARD |
| Dual Sun visors for both driver and passenger | STANDARD |
| Factory installed air conditioning with particulate filter and electronic auto protection for low refrigerant. | STANDARD |
| Dual, heated 7 x 15.75? approximately with Integral 7.4? sq HEATED convex rearview mirrors. Both side mirrors shall be motorized. Both mirrors to be designed to break away when hit from front or rear to minimize damage to mirrors and door structure. | STANDARD |
| Shall be equipped with an air horn mounted under cab. | STANDARD |
| The wiper linkage shall be a heavy-duty formed linkage. Pressed steel linkage is not acceptable | STANDARD |
| The cab noise level shall not exceed 84 dba inside the cab with windows closed, measured at 1800 RPM and at normal road speed. | STANDARD |
| Shall be equipped with an AM/FM Radio, with weather band | STANDARD |
| CB mounting brackets. Compass and outside temp displayed in driver instrument cluster for eyes forward viewing?? | STANDARD |
| Stainless steel sunvisor | STANDARD |
| There shall be a metal mesh protective screen, mounted behind the grill to protect the radiator. | STANDARD |
| Shall have a 70-gallon fuel tank | STANDARD |
| The tank shall be equipped with two non-skid, raised expanded metal steps | STANDARD |
| Shall be mounted on the left or right frame rail UNDER CAB | STANDARD |
| Batteries shall have at least 1,900 cold cranking amps (CCA) and be maintenance-free. | STANDARD |
| Battery Jump studs underhood | STANDARD |
| The battery box shall be right side frame rail mounted | STANDARD |
| All cable ends shall be sealed, and equipped with rubber retainers and covers. | STANDARD |
| 5 auxillary switches | STANDARD |
| Automatic circuit protection for switches | STANDARD |
| Back lit, and labeled rocker panel switches | STANDARD |
| All switches are powered with provisions to label and identify individual switches for specific functions | STANDARD |
| A round 7-conductor, cable shall be wired to the rear of the chassis and terminate into a standard 7 pole trailer connector with ABS. (Conventional Wiring) | STANDARD |
| Shall be equipped with standard generic round or rectangular halogen headlamps | STANDARD |
| Marker lights to be LED mounted in cab or sun visor (if required) | STANDARD |
| ?Body builder wiring to rear of frame, with stop, tail, turn, and marker lights circuits, ignition controlled auxiliary feed and ground for connection of body by supplier | STANDARD |
| The Motor shall have 300 hp peak gross hp at 2100 rpm and 1050 Torque at 1200 rpm. The Motor shall meet all Federal Emissions Standards including 2010 Requirements | STANDARD |
| Shall be equipped with an exhaust brake | STANDARD |
| Maximum road speed to be 65 mph, Idle Set 650 rpm, Resume 1,000 rpm. | STANDARD |
| Cruise control speed to be 60 mph, shall have idle bump up/down feature | STANDARD |
| Shall be equipped with 1250-watt 110 volt block heater, with the plug-in receptacle located on the left side under the driver?s door | STANDARD |
| Shall be dual element, dry-type, with fresh air intake. | STANDARD |
| The air cleaner lid shall have release latches for quick and easy access to the air cleaner. | STANDARD |
| A air filter restriction indicator shall be mounted on the dash | STANDARD |
| Shall be equipped with a temperature controlled, air clutch fan drive | STANDARD |
| Radiator shall be a cross flow with deaeration. System to be filled with extended life coolant | STANDARD |
| Shall be equipped with a coolant filter/conditioner. | STANDARD |
| Antifreeze protection shall be at least ?34 ?. | STANDARD |
| Shall be a DOC & DPF Muffler Shall be a single under chassis horizontal DPF & DOC and vertical tailpipe with 45? chrome tip out. CA shall not be reduced more than 3? by vertical Exhaust Pipe and shield | STANDARD |
| Shall be an Allison 3000 RDS 4th Generation 6 Speed with transmission cooler. | STANDARD |
| Front Axle shall be 14,000 lbs. (axle and suspension) with Stemco-type seals and grit guards or equal and heavy-duty double acting shock absorbers. | STANDARD |
| Reyco 79kb Multi Leaf 23,000 lb with Reyco 4500 lb Aux Springs?? | STANDARD |
| Rear axle ratio shall provide the ability for the truck to achieve a highway speed of 65 MPH. | STANDARD |
| Shall have an air activated rear axle power divider lock with indicator light. | STANDARD |
| Front wheels shall be Hub Pilot 8.25? Disc with 12R22.5 LRH steel belted Radial tubeless tires.. The center wheel hub shall have a thickness of at least .472 inches | STANDARD |
| Rear wheels shall be Hub Pilot 8.25? Disc 11R 22.5 LRG steel belted Radial Traction tires. The center wheel hub shall have a thickness of at least .472 inches | STANDARD |
| Rear Wheels shall be power coated steel | STANDARD |
| Rear tires shall be sized appropriately to achieve a GAWR of 37,000 lbs. | STANDARD |
| All wheels shall have wheel guards installed on all axles. This will include guards between the hub and the wheel as well as in-between each wheel. (Duals) | STANDARD |
| Shall be a Bendix or equal 4- channel anti-lock series air brake system | STANDARD |
| Shall have self-adjusting ?S? cam air brakes front and rear, with brake shields installed. | STANDARD |
| Shall have outboard mounted brake drums, with 16 ? x 5-inch front with 24? long ?stroke chambers | STANDARD |
| All brake blocks shall be non-asbestos | STANDARD |
| Shall have 30 sq. in. MGM TR-TS or equal long- stroke rear brake chambers and 16 ? X 7 rear drums | STANDARD |
| Shall have a 13.2 C.F.M. air compressor | STANDARD |
| Bendix AD-HF Air Dryer | STANDARD |
| To include provision for trailer towing, including tractor protection valve and hand control valve and air brake provision to the end of frame | STANDARD |
| Shall have a Shepherd power steering system or equal. | STANDARD |
| Steering wheel shall be 18 inches in diameter | STANDARD |
| Steering column shall be fully adjustable both vertical and telescoping | STANDARD |