| 2024 Peterbilt 567 | STANDARD |
| Chassis load rating shall be 66,000 lbs. (GVWR) | STANDARD |
| ?217? wb @ 130.8? CA | STANDARD |
| ?130.8? CA @ 217? wb | STANDARD |
| ?115? BBC | STANDARD |
| ? Front frame extension not full depth | STANDARD |
| ?3,468,000 RBM w/ 28.9 section modulus | STANDARD |
| The section modulus at the Motor cut outs shall be at least 18.00, with an RBM of 2,000,000. | STANDARD |
| There shall be no holes or bolts in the top flange of the frame rails. There should be no holes full length on top flange | STANDARD |
| The left frame rail shall be clear, between the fuel tank and the front hanger of the rear spring assembly. | STANDARD |
| Cross-members shall not be riveted to the frame rails, however cross-member components may be riveted to form a cross-member assembly. | STANDARD |
| Shall have a formed steel front bumper, with two front tow loops or hooks accessible through the bumper. | STANDARD |
| Shall be a manufacturer?s premium cab with at least 21 inches of clear space between the driver and passenger seat. | STANDARD |
| Exterior of the Cab shall be painted with Sikkens basecoat /clear coat Omaha Orange 0311 or equal. | STANDARD |
| There shall be stone guard protective screen mounted behind the grill to protect the radiator. | STANDARD |
| Voltmeter gauge | STANDARD |
| Motor oil pressure gauge. | STANDARD |
| Tachometer and Hour meter | STANDARD |
| Visual and audible low oil pressure / high coolant temperature warning system | STANDARD |
| Motor coolant temperature gauge | STANDARD |
| High output heater w/fresh air selection. The heater shall have a 30,000 BTU rating | STANDARD |
| Dual Sun visors for both driver and passenger | STANDARD |
| Factory installed air conditioning with particulate filter and electronic auto protection for low refrigerant. | STANDARD |
| Dual, heated 7 x 15.75? approximately with Integral 7.4? sq HEATED convex rearview mirrors. Both side mirrors shall be motorized. Both mirrors to be designed to break away when hit from front or rear to minimize damage to mirrors and door structure. | STANDARD |
| Shall be equipped with an air horn mounted under cab. | STANDARD |
| The wiper linkage shall be a heavy-duty formed linkage. Pressed steel linkage is not acceptable | STANDARD |
| The cab noise level shall not exceed 84 dba inside the cab with windows closed, measured at 1800 RPM and at normal road speed. | STANDARD |
| Shall be equipped with an AM/FM Radio, with weather band | STANDARD |
| CB mounting brackets IPO pocket. Compass and outside temp displayed in driver instrument cluster for eyes forward viewing?? | STANDARD |
| Stainless Steel Visor | STANDARD |
| There shall be a metal mesh protective screen, mounted behind the grill to protect the radiator. | STANDARD |
| Shall have a 70 gallon fuel tank | STANDARD |
| The tank shall be equipped with two non-skid, raised expanded metal steps | STANDARD |
| Shall be mounted on the frame rail, undercab | STANDARD |
| Shall not extend more than 6 inches past the back of the cab or otherwise inhibit the installation of mounted bodies or equipment | STANDARD |
| ?Paccar 160 amp brush type | STANDARD |
| Batteries shall have at least 1,900 cold cranking amps (CCA) and be maintenance-free. | STANDARD |
| ?Battery box cover constructed in aluminum | STANDARD |
| All cable ends shall be sealed, and equipped with rubber retainers and covers | STANDARD |
| 5 auxillary switches | STANDARD |
| Automatic circuit protection | STANDARD |
| Back lit, and labeled rocker panel switches | STANDARD |
| Bidder must ensure that the control panel on all equipment associated with this purchase are wired and labeled uniformly | STANDARD |
| A round 7-conductor, cable shall be wired to the rear of the chassis and terminate into a standard 7 pole trailer connector with ABS. (Conventional Wiring) | STANDARD |
| Shall be equipped standard style halogen headlamps | STANDARD |
| ? Supplier splices into the factory wiring harness is unacceptable and may be grounds for bid rejection | STANDARD |
| the Motor shall have 390 hp peak gross hp at 2100 rpm and 1400 Torque at 1200 rpm. The Motor shall meet all Federal Emissions Standards including 2010 Requirements | STANDARD |
| Shall be equipped with a compression Motor brake | STANDARD |
| Electronic Motor Controls (Shall have): | STANDARD |
| ????????? Maximum road speed to be 65 mph | STANDARD |
| ????????? Cruise control speed to be 60 mph | STANDARD |
| ????????? Automatic Idle shut down to be 10 minutes | STANDARD |
| ????????? Idle, set 650, Resume 1,000 | STANDARD |
| ????????? Shall have idle bump up/down feature | STANDARD |
| ????????? Shall be equipped with 1500-watt 110 volt block heater, with the plug-in receptacle located on the left side under the driver?s door. | STANDARD |
| Shall be dual element, dry-type, with fresh air intake. | STANDARD |
| An air filter restriction indicator shall be mounted on the dash; and it must indicate restriction for both elements. | STANDARD |
| The air cleaner lid shall have release latches or thumbscrews for quick and easy access to the air cleaner | STANDARD |
| Shall be a DOC & DPF Muffler Shall be a single under chassis horizontal DPF & DOC and vertical tailpipe with 45? chrome tip out. CA shall not be reduced more than 3? by vertical Exhaust Pipe and shield | STANDARD |
| ?Allison 4000 RDSP, | STANDARD |
| Front Axle shall be 20,000 lbs. with Stemco-type seals or equal and grit guards, and heavy-duty double acting shock absorbers, with 20,000 lb. Multi-leaf springs. | STANDARD |
| Rear Axle shall be 46,000 lb capacity, and have a Hendrickson HMX460-54 or equal suspension with a 46,000 lbs. rating and a gear ratio to allow 65-mph. | STANDARD |
| Shall have a lube pump and an air activated rear axle power divider lock with indicator light. | STANDARD |
| Shall be a Bendix anti-lock series or equal air braking system. | STANDARD |
| Shall have self-adjusting ?S? cam air brakes front and rear, with shields installed. | STANDARD |
| Shall have outboard mounted brake drums, with 16 ? x 6-inch front drums and 16 ? X 7 rear drums | STANDARD |
| Shall have 30 sq. In. MGM TR-T series rear brake chambers, or equal and the chambers shall be tilted in the upward position for paver operations | STANDARD |
| All brake blocks shall be non-asbestos | STANDARD |
| Shall have at least a 15.9 CFM Capacity air compressor | STANDARD |
| ?Bendix AD-HF EP air dryer | STANDARD |
| Seat shall be a cloth covered high back National or equal air ride seat, with air lumbar and inboard arm rest. | STANDARD |
| Passenger seat shall be a cloth covered high back National high back, air suspension matching driver | STANDARD |
| Both seats shall have compatible; three point type seat belts with shoulder strap, and retractors, orange in color | STANDARD |
| Shall include an operator's manual | STANDARD |
| Shall include free access to online parts manuals and chassis build sheets searchable by VIN number to include cab and chassis, Motor and transmission | STANDARD |
| 5 year SmartLink subscription | STANDARD |
| Shall have a dual Shepherd power steering system or equal. | STANDARD |
| Steering wheel shall be 18 inches in diameter | STANDARD |
| Steering column shall be fully adjustable both vertical and telescoping | STANDARD |
| Front wheels shall be Hub Pilot with 385 425/65R 22.5 LRJ steel belted radial tubeless tires. | STANDARD |
| Rear wheels shall be Hub Pilot with, 11 R 22.5 LRG steel belted radial traction tires. The center hub shall have a thickness of at least .472 inches | STANDARD |